As winter approaches, many homeowners start to worry about potential plumbing problems. While some issues may be specific to colder weather, others can occur at any time of year. Here are four of the most common plumbing problems and how to fix them.
For Winter Plumbing Inspection in Indianapolis, Call 317-784-1870 Today.
Four Winter Plumbing Problems to Watch Out For This Season
1. Frozen Pipes
Frozen pipes are a common plumbing problem in the winter. If the water in pipes freezes, it can cause them to burst. To prevent frozen pipes, you can insulate them or wrap them in heat tape. You should also make sure that your home is properly heated during the winter. If you do experience frozen pipes, you can use a hairdryer to thaw them out. However, if the pipes have already burst, you’ll need to call an Indianapolis plumber.
2. Clogged Drains
Clogged drains are another common plumbing issue in cold weather. They can be caused by food particles, grease and soap buildup, or leaves and other debris. To prevent clogs, use screens over your sinks and shower drains and avoid pouring grease or food down the drain. You can also use a plunger to clear out any minor clogs, but if it doesn’t work you should call a plumber for help.
3. Leaky Faucets
Leaky faucets are often caused by worn out washers or old valves. To fix them, you’ll need to replace the washer or valve. This is a simple repair that you can do yourself, but it will require some basic plumbing tools and knowledge.
4. Water Heater Issues
Water heaters can be temperamental in cold weather. If your water isn’t heating up properly, make sure that the thermostat is set to the desired temperature. You should also make sure your water heater is well insulated, as this will help prevent it from freezing. If you don’t feel comfortable inspecting or repairing the water heater yourself, you should call a plumber for assistance.
Conclusion
With these tips in mind, you can be better prepared for any winter plumbing problems that may arise. With a bit of proactive maintenance and quick action, you can keep your plumbing system running smoothly this winter.
Your in-ground sprinkler system can be an important part of your garden’s health and beauty. But during the winter months, when temperatures drop, it’s important to remember that your sprinkler system needs some special attention before the cold hits.
Continue below to review a quick and easy guide to blowing out your inground sprinkler system for winter, plus where to get the best seasonal plumbing service near you.
For Seasonal Plumbing Services in Indianapolis, Call 317-784-1870 Today!
Winter Maintenance for Underground Sprinkler Systems
Blowing out your inground sprinkler system is one of the best ways to protect your pipes against freezing and can help you avoid costly plumbing repairs come springtime. Here are the simple steps to getting the job done right the first time, every time:
How to Blow Out an In-Ground Sprinkler System:
The first step in blowing out your inground sprinkler system is to locate the main water shut off valve. This will usually be located close to where the water supply enters your home. Once you’ve found this valve, turn it off completely until spring when you’re ready to use your sprinkler system again.
Next, you’ll need to connect a garden hose to one of the last sprinkler valves in your system. Run the other end into an area where it can safely drain without causing any damage (such as a grassy area). Finally, turn on all your sprinkler valves, starting with the first one closest to the main water shut off valve.
Once you’ve done this, turn on an outside faucet and let it run until nothing but air comes out of your sprinkler system pipes. This will help clear the remaining water from your pipes and ensure that they don’t freeze during the winter months. Once you’re done with the faucet, turn it off and close the shutoff valve you opened earlier.
Winter Sprinkler System Protection and Plumbing Maintenance
By following these steps, you can ensure that your in-ground sprinkler system is well-protected during winter months. If you have any questions about blowing out your inground sprinkler system or need help with other seasonal plumbing maintenance tasks, contact a local Indianapolis plumbing company for trusted assistance.
Are you looking for a trusted plumber to help you get your home or business equipped for the upcoming winter climate?Contact Weilhammer Plumbing Company at 317-784-1870 for licensed and insured plumbing service in Indianapolis, Indiana. We serve residential and commercial clients and are state-licensed master plumbers.
The leaves have been falling for quite some time now, which means the ground is saturated with tree remnants. Hopefully you have your plumbing maintenance checklist in motion! It is important to get your fall season plumbing care needs out of the way before the winter freeze is upon us.
Continue below to learn some of the most important elements of fall plumbing maintenance, plus who to trust in Indianapolis for superior plumber service and repair at an affordable price.
Fall Plumbing Service Indianapolis Indiana 317-784-1870
Fall Plumbing Service Checklist
It’s that time of year again! As the leaves start to change fall from the trees, it’s time to think about preparing your home for the colder months ahead. One of the most important things you can do is make sure your plumbing is in good working order. After all, you don’t want to be dealing with a burst pipe or a clogged drain when it’s freezing outside!
Here is a helpful plumbing care checklist for the fall season:
1. Check all of your outdoor faucets and hose connections for leaks. If you find any, make sure to repair them before the cold weather sets in.
2. Disconnect and drain all outdoor hoses. Store them indoors for the winter.
3. If you have an in-ground sprinkler system, have it professionally winterized before the first freeze.
4. Inspect your gutters and downspouts to make sure they are clean and free of debris. Clogged gutters can lead to water damage and foundation problems.
5. If you have a sump pump, make sure it is in good working order and that the batteries are fresh. A sump pump is your first line of defense against basement flooding.
6. Inspect all exposed pipes, both inside and outside your home, for signs of leaks or damage. If you find any, have them repaired as soon as possible.
7. If you have a water softener, have it checked and serviced if necessary.
8. Have your septic system pumped and inspected if you have one.
By following this simple plumbing maintenance checklist, you can help avoid costly repairs and ensure that your home is ready for the colder months ahead.
Do Not Skip Routine Plumbing Service
Routine plumbing repair and service is important to keep your system running smoothly. Skipping inspections and maintenance can lead to costly repairs and health hazards. Plumbers in Indianapolis can identify and fix small problems before they become big ones, so it’s important to schedule regular service appointments.
If your bathtub is draining slowly, there are a few different things that could be causing the problem. First, check the drain for a clog. If the drain is clear, try to clean out the P-trap. If neither of these solutions works, you may have a leak in the drainpipe. Continue below to learn more about these 3 common bathtub drain problems, plus what to do about them.
Bathtub Plumbing Repair Indianapolis Indiana 317-784-1870
Top 3 Causes of a Slow Draining Tub
One of the most common reasons why your bathtub is draining slowly is because of a clog in the drain. Over time, hair, soap scum, and other debris can build up in the drain, causing a blockage. This can cause water to drain slowly, or even back up into the tub. If you notice that your bathtub is draining more slowly than usual, you may want to check the drain for a clog.
Another reason why your bathtub may be draining slowly is because of a problem with the P-trap. The P-trap is a curved pipe that connects the drain to the main sewer line. It traps water in order to prevent sewer gases from entering the home. Over time, the P-trap can become corroded or clogged, which can cause water to drain slowly. If you suspect that the P-trap is the problem, you can try to clean it out with a plunger or a plumber’s snake.
Finally, another possibility is that there is a leak in the drain pipe. This can happen if the drainpipe is old or has become damaged. A leak in the drainpipe can cause water to drain slowly, or even to back up into the tub. If you think that there may be a leak in the drainpipe, you should call an Indianapolis master plumber to have it repaired.
Troubleshooting Bathtub Drainage Issues
Bathtub drains can be a source of frustration when they become clogged or slow to drain. Luckily, there are a few simple troubleshooting tips you can try to get your drain flowing again. If your tub drain is clogged, the first step is to try using a plunger to dislodge the obstruction. In the case that doesn’t work, you can try using a drain snake or auger to reach down into the drain and clear the blockage. If the bathtub is slow to drain, it may be due to a build-up of hair and soap scum, as mentioned earlier. Again, you can try removing this buildup by using a plumbers’ snake or a drain cleaner specifically designed to break up soap scum.
If you’re still having trouble with your bathtub in any way, shape, or form, it’s time to call in a professional plumber in Indianapolis for help. They will be able to quickly diagnose the problem and get your drain flowing freely again.
Whether you are a first-time homeowner or have owned your house for a long time, it is vital to stay up to date with your plumbing systems. Reviewing some common tips and general information from time to time can refresh your memory and help you do a better job of taking care of your home. Continue reading to review some unique, but important, frequently asked questions about home plumbing.
Residential Plumber Indianapolis Indiana 317-784-1870
Home Plumbing FAQS You Want to Know
What is Hard Water?
Hard water is water that is polluted with high levels of contaminates, such as iron salts, calcium, and magnesium. If you are starting to notice subtle changes in your dishes, skin, laundry, and plumbing fixtures, it may be related to a hard water issue. A water filtration system, coupled with a quality water softener, can eliminate these mineral ions plus reduce the level of hardness in your home’s water.
Why Does My Water Take So Long to Heat Up?
There are some common reasons why your water heater might be taking too long to heat your water up. Most often, the water heater is just too old or defective. Otherwise, you could have too much sediment buildup at the bottom of the tank, low volume restrictors installed on your plumbing fixtures, or too much distance between the location of the water heater and your point-of-demand. To fix this problem, you will need to contact a professional Indianapolis plumber who specializes in hot water heater repair and service.
How Do I Unclog a Backed Up Toilet?
Large debris can get stuck, like toilet paper, hair ties, and more. In this case, you will need to use your plunger to plunge the toilet bowl for 30 seconds. But before you do, be sure there is not too much water in the toilet bowl. If there is, empty as much water as needed with a separate cup or bowl. Try flushing the toilet to see if the plunger loosened up the clog. If it didn’t, try again or check to see if the flapper is the issue. If you cannot clear a clogged toilet bowl with a plunger, then you will need to call a licensed plumber for help.
How Do I Remove the Crusty Substance on the Shower Head and Faucet?
Remove the shower head by unscrewing it from the spout. Place it in a bowl with hot water and one cup of household vinegar. Leave it overnight then scrub it clean the next morning. If you cannot screw the shower head off, put the vinegar solution in a plastic bag and place it over the spout, attaching and securing it with a tie. If the substance does come off completely, re-do the process using less water and more vinegar.
How Do I Get Rid of Odor in My Garbage Disposal?
The odor most likely is coming from an accumulation of food scraps and other debris. To remove the smell, you can put a mixture of ice cubes and lemon peels down the disposal and run it, then with disposal still running, flush it with cold water for a minute. If this does not do the trick completely, add a few drops of dish soap with cold water for another thirty seconds. This household remedy is a popular solution to foul smelling garbage disposals.
How Often Should a Septic Tank Be Pumped?
An inspection or cleaning should be done once every few years or so, depending on the size of the make and model septic system in place. In smaller systems, once every three years is sufficient; however, a large tank would require an inspection once every two years or less. The larger the system, the more often it will require service.
Am I Smelling Natural Gas in My House?
Natural gas smells like rotten eggs. If you smell this in your home or building, first, turn off all appliances that use gas. Then open a few windows or doors to let the gas air out. Once you have done this, check the range, water heater, and furnace pilot lights; if one light is out, relight it. If they are not the issue, call your local gas provider and report the smell right away.
Why Did My Plumbing Pipes Go Bad?
There are several reasons why plumbing pipes go bad. It can be due to old age, poor installation, incompatibility, material quality issues, corrosion, external structural damages, and much more.
Should I Re-Pipe or Repair the Plumbing?
In many cases, plumbing pipes do not require replaced, but rather repaired. If one or two plumbing pipes burst or incur some sort of damage, they can simply be replaced through trenchless piping or other repair techniques. However, there are other cases in which the whole house plumbing system should be re-piped. Talk to in Indianapolis plumber to determine the best course of action for your plumbing pipe renovation needs.
How Do I Know if I Have a Plumbing Leak?
As someone who regularly pays your water and energy bills, you know when something is a little off. Suddenly higher utility bills are one of the first signs of a hidden plumbing leak in the home. If you are utility bills are higher than usual, or have seen a sudden spike in cost, it could be an indication that you have a hidden plumbing leak somewhere in your system. First, contact your utility company to confirm that your bill is correct, and if it is, your next step is to contact in licensed plumber for a home plumbing inspection in Indianapolis.
Do you think your plumbing system could use some TLC?Contact Weilhammer Plumbing Company at 317-784-1870 for professional plumbing services in Indianapolis, Indiana. We serve residential and commercial clients and are state-licensed master plumbers.
Although there are drain augers and plastic drain snakes available on the market, these should only be used for minor clogs. If you are experiencing moderate to severe drain issues, you need comprehensive drain cleaning, which is a service that should only be carried out by a licensed and insured plumbing professional.
Continue reading to learn why such plumbing services are strictly for trained and equipped professionals, plus where to get a free estimate for drain clearing and cleaning in Indianapolis.
Drain Cleaning Service Indianapolis Indiana 317-784-1870
Common Signs of Drain Trouble
It is easy to tell when you have a minor clogged drain problem. A slow draining sink or bathtub is likely the result of a minor obstruction or blockage within the drain itself. Typically, this is caused from shampoo and soap residues, hair, and general dirt and debris. Even if the drain is entirely clogged, it is likely a minor blockage that can be dislodged using a plunger or drain snake. On the other hand, a drain snake does not work on tougher drain problems, which tend to evade your attention for some time because they happen out of view. This is why regular home plumbing inspections are important.
Some common signs of moderate to major drain clogs include:
▭ A clogged drain that will not dislodge with a plunger or drain snake. ▭ A burst or leaking plumbing pipe. ▭ Water leaking from the base of the toilet. ▭ A bubbling toilet. ▭ Drains that smell bad. ▭ Puddles around the bathtub, shower, or sink.
If you are experiencing one or more of these drain issues, you will need to quickly hire a licensed plumber who can provide professional drain clearing and cleaning services.
The Importance of Hiring a Professional for Drain Repair and Cleaning
Professional plumbers are licensed and insured to perform comprehensive drain repairs and drain clearing services. They retain the proper permits, training, equipment, and resources to clean drains according to local building codes. In many cases, moderate to severe drain problems must be approached using video pipe inspection equipment and high-powered hydro-jetting technology, which uses high pressured hot steam to release and clear drain blockages. For less serious drain issues, a plumber may use a commercial hand-crank drain snake or motorized auger with success.
Whether you call it a drain snake, plumber snake, or small drum auger, virtually every renter and homeowner has one. You can purchase a drain snake at the grocery store, the dollar store, the home improvement store, and at almost any online retailer of the sort. They are easily accessible and very inexpensive, so they are a highly recommended tool to have around the house. You can even use them to unclog toilets, showers, and tubs. But sometimes, plastic augers are just not enough to unclog a stubborn sink drain.
If you are attempting to unblock a clogged sink, but the plumber snake isn’t working out, continue reading for some drain clearing tips that will help you get past this common, but oh-so-frustrating, obstacle.
Sink Drain Repair Indianapolis Indiana 317-784-1870
Why is the Drain Snake Not Working?
Drain snakes are easy tools to use, so you will know right away whether yours is working or not. To use a drain snake, you insert it deep into the drain, twist it around several times, and then pull it back up. The auger should pull out all sorts of unsightly materials, like hair, soapy residue, and dental floss.
Although very effective tools, they are not always the right choice for a clogged drain. In fact, there are many reasons why a drain snake might be ineffectively unclogging your sink. One of the most common in easily fixable reasons why a drain auger won’t work is because the old clogging material is still attached to the rod. Be sure to fully clean your drain auger before reusing it for another clog.
Another common reason why augers fail to do the trick has to do with the structural integrity of the auger itself. If you are using a small drum auger rather than a plastic drain snake, it is possible that the thumbscrew has come loose. If the thumbscrew is loose, the auger will not be able to effectively rotate. And if the auger will not rotate, it won’t be able to catch and pull any debris or blockage within the drain.
If you can’t even push the auger down into the drain, it’s because there is a heavy blockage that is denser than the overall tensile strength of the tool. In this case, you would need something more heavy-duty to dislodge the blockage, or perhaps even more invasive plumbing repair. Severe sink clogs are difficult to repair with a plumber snake.
What to Do About a Clogged Sink
If your drain snake is not working, but none of the above-mentioned reasons are to blame, you have two viable options: attempt to loosen the clog with a drain cleaner and repeat the auger process again, or save time and effort by contacting a professional Indianapolis plumber for drain clearing service. Just be sure you do not ignore a clogged drain, as they can lead to more serious plumbing problems, like burst pipes and water leaks.
Looking for a professional plumber who can make all of your plumbing problems go away without breaking the bank?Contact Weilhammer Plumbing Company at 317-784-1870 for licensed and insured plumbing services in Indianapolis, Indiana, and its surrounding counties. We serve residential and commercial customers.
Nothing quite drains the pleasure out of your morning or post-work shower than standing ankle deep in soapy water. If your shower drain is clogged, it is important to troubleshoot the issue as soon as possible, not just for the sake of your bathing enjoyment, but also for preventative maintenance purposes. Fortunately, there are many things you can do on your own that can solve the problem right away.
Continue reading to learn the top 7 things you can do to unclog your shower drain.
Drain Clearing Indianapolis Indiana 317-784-1870
How to Fix a Clogged Shower Drain
So, what causes a shower drain to clog up? Well, the answer is quite obvious. Mostly, hair, dirt, and soap residues are to blame, but shower drains can also fall victim to obstructions caused by thick shaving cream, lost jewelry, razor caps, toys, and all sorts of other common bath time accoutrements. Many people like to brush their teeth and floss in the shower, so floss is a common obstruction found in shower drains.
Not to worry, as there are plenty of ways to unclog that troublesome shower drain of yours! Here are the top seven things you can do to unclog your shower drain:
Manual Dislodging
The first thing you want to do to fix a clogged shower drain is to manually dislodge anything that’s obstructing the drain. Any visible obstructions like hair or soap scum should be cleared away of your shower drain before testing other methods of repair. Yes, this will be a slimy and unpleasant task, so put on some rubber gloves and possibly even a face mask.
Plunger
When your manual attempt doesn’t work, grab your plunger. Use the plunger over the shower drain in the same way you would use it in the toilet if the toilet were clogged. Place the plunger directly on top of the shower drain and pump it several times with force. Then run the shower to see if the water flows through the drain smoothly. If that doesn’t work, you may need to get deeper inside the drain. The next few methods will help you do that.
Boiling Water
If the first two methods don’t work, boil some water on top of your stove, and then pour it down your shower drain. Sometimes this can clear out shaving cream, dirt accumulation, and soap scum buildup. Once these residues are cleared, your shower drain should flow smoothly. Just be careful when you’re handling the boil water because it will burn you.
White Vinegar and Baking Soda
If boiling water isn’t strong enough, make a concoction of distilled white vinegar and baking soda. Then pour the solution down your drain. This is basically a homemade drain cleaner, but without all of the harsh chemicals and damaging ingredients. You may need to repeat this a few times to get the drain entirely cleared. Oftentimes, this vinegar and baking soda solution is well paired with an auger, also known as a drain snake.
Drain Snake
A drain snake is a long, thin, plastic, flexible, handheld auger that is used to dislodge any obstructions within a drain. Drain snakes can be purchased for as little as one dollar at any local department or grocery store. You can literally find them anywhere that sells regular home goods or household products. To use an auger, simply push it deep into the drain as far as you can, then turn it a few times before pulling it out. You will be shocked to see what comes out with it!
Wire Hook
You can also use a metal hook in the same way you would use a drain snake to dislodge any obstructions within the shower drain. Just be careful using this method because you can accidentally poke or stab yourself. Most people will take a wire hanger and unwind it to form a hook and handle. This works really well when you don’t have an auger on hand.
Licensed Plumber
Your last resort is to contact a licensed Indianapolis plumber for drain cleaning and clearing service. They have the proper tools and resources to promptly resolve drain issues. Because drain clearing is typically an easy and speedy service, you can expect it to be affordable as well.
Many store-bought cleaning agents contain high amounts of harmful chemicals and toxic solutions. Not only can these be dangerous to humans, pets, and wildlife, but they can also damage your home’s plumbing systems, appliances, and more. So, let’s keep the Earth Day momentum going by introducing some non-toxic, homemade cleaning solutions you can use all around the house and beyond! Continue below to get started with some easy recipes you can make right at home.
Indianapolis Plumber 317-784-1870
Why Make Your Own Cleaners
Various products on the market today fail to specify their dangerous chemicals on the ingredients label. So, the best way to avoid contact with these types of dangerous products is to simply replace them with safer alternatives. Making your own chemical-free, non-toxic household cleaning products is extremely rewarding. Best of all, it is a lot less expensive and easy to do!
Simple and Safe Homemade Cleaning Solutions
Purchase quality spray bottles. Be sure to choose bottles with ounces measured on the outside of them. This will help you measure and mix solutions quicker and easier. Also, always label each bottle with the type of cleaning agents inside. For example, if the solution is for your kitchen, label it, “kitchen cleaner”, or something similar. Safe ingredients that can be used to create your own homemade cleaning solution range from vinegar and baking soda to borax, Castile soap, and essential oils. Make your own combinations and experiment with what works best for your cleaning goals and even allergies.
Safe and Non-Toxic Ingredients Include, But are Not Limited To:
❧ Distilled White Vinegar ❧ Baking Soda ❧ Borax or Washing Soda ❧ Olive Oil-Based Soap ❧ Coconut Oil-Based Soap ❧ Vegetable Soap ❧ Castile Soap ❧ Fresh Squeezed Lemon Juice ❧ Essential Oil ❧ Clean Water
⚠ Safety Warning ⚠ Although you are making Eco-friendly and safe cleaning products, it is still strongly encouraged to keep them locked up and out-of-reach from children, pets, and wildlife. No one wants to be responsible for a sick animal or child. If these solutions are ever ingested in large quantities, immediately contact emergency services for medical attention.
How to Use Your New Cleaners
When it comes to cleaning your kitchen with Eco-friendly solutions, use a mixture of baking soda, Borax, or washing soda with a little bit of vegetable soap and warm water. This solution can be applied on counters, floors, appliances, and other surfaces.
For ovens and appliances, mix baking soda and washing soda with a little bit of water to make a paste. Generously apply the paste and allow it to sit overnight. Then wash away in the morning for best results.
For countertop cleaning, gently scrub an even mixture of these same ingredients, and then rinse with clean water.
For cutting boards, use a mixture of vinegar and 3% hydrogen peroxide. Bottle each solution separately, spraying first with the vinegar and second with the hydrogen peroxide. Repeat these steps until you achieve a clean surface.
Drains, Sinks, Tubs, and More
Use the same solutions and recipes for bathroom tile, bathtubs, bathroom countertops, toilets, and sinks. For drains, use a combination of baking soda and vinegar. First poor half cup of baking soda down the drain, and then pour 1 cup of vinegar down the drain. Allow the drain to rest for a few minutes and then run hot water through the drain until it is unclogged.
Are you experiencing cloudy or spotty dishes? How about clogged drains or smelly water? Solve your plumbing issues soon, before they can get worse, and costlier!Contact Weilhammer Plumbing Company at 317-784-1870 for professional plumbing service and repair in Indianapolis, Indiana and its surrounding counties. We serve residential and commercial clients.
Is you dishwasher not draining the way it should? Have you noticed a musty puddle of water at the bottom of the well after you run a load? If so, you are most definitely experiencing dishwasher machine drainage problems. Continue below to learn some troubleshooting tips for a problematic dishwasher that won’t seem to drain water.
Dishwasher Repair Indianapolis Indiana 317-784-1870
Flooded Dishwashers are a Sign of a Plumbing Issue
We understand the frustration you feel when you expect to open up your dishwasher to a freshly-cleansed load of dishes but get a waterfall of dirty, soapy water instead. Unfortunately, there is no amount of Rinse-Aid to eliminate the excess moisture. This is a dishwasher draining issue. Before getting into the reasons why your dishwasher is doing this, it is important to note that this type of problem calls for professional plumbing inspection and repair. Contact a licensed plumber in Indianapolis for dishwasher repair and water drainage repair services you can trust.
Common Causes of Poor Water Drainage in Dishwashers
There are a number of possible reasons why dishwashers fill up with water and fail to drain properly, yet in the plumbing industry, the most common seem to be garbage disposal backups, drain hose disconnections, and dirty drain filters. Additional causes include faulty pumps, design defects, and even motherboard malfunctions. Be sure to disconnect the power to your dishwasher before performing any type of inspection, and certainly before you intend to tamper around with it.
Dishwasher Not Draining? Check These 3 Things Before Calling a Plumber:
Backed-Up Garbage Disposal
An obstruction or clogged garbage disposal can have an affect on the water drainage quality of your dishwasher. With long-term or major backups, dishwashers cannot drain properly after a cycle. Start your troubleshooting by clearing your garbage disposal. With a stream of hot water running next to the sink drain (not in the drain), flip your disposal on for 30 to 45 seconds. You can also use some liquid dishwashing soap to help loosen any obstructions.
Optional: Turn the power off to your garbage disposal. Then inspect the inside of the sink drain for any objects of obstructions.
Disconnected Drainage Hose
Often times, drain hoses that are attached to the sink or garbage disposal get knocked out of place, shifted, or even kinked. Before calling a plumber about your dishwasher drainage problems, check to see if these hoses are connected and in good condition. A worn-out or old drain hose should be replaced. This too could be the root of your plumbing issue.
Dirty Drain Filters
Drain filters, like all other filters, require routine cleaning or replacement, depending on what kind of filter product they are. If your dishwasher is not draining all the way after you run a cycle, it could be due to a dirty drain filter that is saturated with food particles, grease, soap residues, and more. Refer to your dishwasher owners’ manual for manufacturers’ instructions on how to access and clean the drain filter.
